What is the default factory password for Brocade switches?

Brocade FC-Switches are equipped with four default useraccounts: admin, root, user and factory. By connectiong an SSH session with user ‘root’ and default password ‘fibranne’ you will be prompted to change logins for accounts root, user and factory.

How do I access my Brocade SAN switch?

Accessing GUI of Brocade SAN Switch without Broswer

1. Console to the Brocade SAN Switch with default username = admin & Password = password to configure the IP Address Warning: Default password not changed for ‘root’.
2. Install the latest JAVA version.
3. Add the IP Address of the SAN Switch to Exception Site List in JAVA.

How do I change my Brocade admin password?

including setting password rules, refer to the Security chapter of the Brocade Network OS Administrator’s Guide.

1. Enter the configure terminal command to enter global configuration mode.
2. Enter the username command followed by the account name and the password parameter.
3. When prompted, enter the new password.

How do I reset my Brocade SAN to factory settings?

Resetting the Brocade FC switch to factory defaults

1. Log in to the switch as an administrator.
2. Disable the Brocade Virtual Fabrics (VF) feature:
3. Disconnect the ISL cables from the ports on the switch.
4. Disable the switch:
5. Disable the configuration:
6. Clear the configuration:
7. Save the configuration:

How do you reset a Brocade switch?

Tap the “Enter” key a few times and the Brocade command prompt will display. Type the console password if requested and press the “Enter” key. Type “configDefault” and press the “Enter” key. The switch configuration is now reset to factory default settings.

How do I change my SAN switch password?

If you have the IBM Smart Analytics System Control Console installed, then you must use the Control Console to change passwords on the SAN switch using the “miauth -pw” command.

How do I connect to Brocade?

Connecting to the CLI

1. Connect the workstation to the Ethernet network containing the HPE Synergy Frame Link Module.
2. Connect to the switch using ssh or open a Telnet connection using the IP address set earlier.
3. Enter the user name, using an administrative account.
4. Enter the password.
5. Verify the login was successful.

How do I add zoning to my Brocade switch?

How to create zones from CLI on a Brocade SAN Switch

1. admin> switchshow.
2. Note:Any devices that connect using NPIV use nsshow command to find the WWPN addresses logged in to the port.
3. 2.Run the cfgshowcommand.
4. admin> cfgshow.
5. cfgshow will display the configuration and how the zoning is currently configured.

How do I enable root user in Brocade switch?

switch:admin> userconfig –show root

1. Verify that Account name is root.
2. If the Enable attribute that is shown is Yes, then root account is now enabled.

How do you reset a Brocade SAN switch?

How do I delete a zone in Brocade SAN switch?

1. Putty to switch02 (xx.xxx.xxx.xx)
2. Backup existing zone configuration (This step is not mandatory but is a best practices always to backup zone configuration before making changes)
3. Remove the zones from active zone configuration; Delete zones & alias from zone database.
4. Logout of putty.

How do I reset my Brocade SAN switch password?

Enter the passwddefault command to reset the root password to the factory default value or the /sbin/passwddefault -f (to reset the root password and forcefully enable the root account).

What is the default password of “Admin” in brocade switch?

The default password of “admin” is “password”. The OS of brocade switch uses Linux 2.6 kernel. The root is super administrator account. Disclaimer for Root and Factory Accounts Usage!

Does Brocade DCX upgrade reset passwords to default?

Summary: Passwords were reset to default on Brocade DCX upgrade from FOS v6.1.1_enc2 to v6.2.0. This tip should be reviewed in 6 months in the event that Brocade decides to change the default login back to the IBM standard.

Do Brocade switches have accounts for root and factory?

The Brocade switches are basically running a proprietary version of LINUX that does have accounts for ROOT, FACTORY, ADMIN, and USER that are created at the factory. On the old 1GIG switches prior to V2.6.0 software, you where not prompted to change any of these password.

How to change the default passwords of the accounts?

It is important not to use default passwords in a productive environment, so therefor please change the passwords. Change the passwords of the accounts root, user and factoryby using SSH. At the first login you will be prompted to set new password. With ENTER you can start the process by pressing Ctrl-C you can abort the process.