Why is my coil rusting?

We know that rust occurs when oxygen interacts with the metal, and also when liquid is exposed to it. So, the longer your pod coil has been sitting saturated with juice, the more likely it is that you’ll start to see rust. Also, the more exposed to oxygen it’s been, the more likely rust is to occur.

Can a coil go rusty?

Will a Coil Actually Rust? The short answer is yes, vape coils can get rusty. Though it’s fairly uncommon, those coils are made from, of course, metal, which is not immune to rust. So, if your coil appears rusty, your eyes might not be deceiving you after all.

How do I know if my RDA coil is bad?

There are 4 factors to look for to know when it is time to replace your coils.

1. Poor vapor production.
2. Burnt vape taste.
3. Lingering flavors of e-juice.
4. A gurgling sound.

How long do RDA coils last?

On average, a decently constructed coil for a sub-ohm tank should last you 4 days to 1 week. If you vape less because you cannot vape during work hours, or you do not vape throughout the day, then your coils are likely to last twice as long.

When should I change RDA coil?

Short answer: when the resistance is increased between 10% to 20% or if only 2-3 wraps are glowing during dry burn. The research was done on dual Fuzed Clapton SS316 coils for 4 months.

Can a coil burn in one day?

It could be potentially a dry-hit, and your coil isn’t in fact burnt. Next time you notice it, try setting your vape down for a few minutes and seeing if it recovers. It’s entirely possible and plausible that your coils aren’t wicking swiftly enough to keep up with the rate you’re vaping.

Why does my coil taste burnt after 2 days?

It tastes burnt because the wick inside your atomizer coil has dried out and burned up when it was heated. The wick is the part of your vaporizer that soaks up the eliquid from the tank. The wick holds onto this eliquid before it is turned into vapor when the coil heats up.

How do I clean my RDA coils?

1. Step 1: Disassemble your RDA. Remove from the packaging and inspect your RDA for any damages.
2. Step 2: Wash your RDA. Mix your bowl of warm/hot water with dish soap and put everything inside the bowl.
3. Step 3: Rinse and Dry.
4. Step 4: Reassemble and Build.
5. Step 5: Enjoy!

How long does kanthal last?

Depening on the diameter of the wire, Kanthal 0.35mm will last 5-10 dryburns, while Kanthal 0.40mm will last about twice as long. Given the fact I vape 30ml per day, IF I was using always the same device, for me a coil made with Kanthal 0.35mm would last about one day, including 5 dryburns.

Why do my RDA coils burn so fast?

When you vape at a higher wattage, you vaporise more juice with each puff. This is great if you want big clouds, but it can also impact your coils. Since you’re vaping e-juice at a faster rate, sometimes your wick struggles to soak up juice quickly enough to keep up. And when it can’t keep up, you can burn your wick.

Why do my coils burn up so fast?

Sub-ohm coils heat up much quicker than those with a higher resistance. If your e-liquid has a thinner consistency then the atomizer head can vaporize it too quickly, causing premature burning.

How much resistance should I expect from my RDA coils?

Also, make sure your RDA has post holes big enough to fit the legs of the coils. It’s also important to remember that our resistance listed is for ONE COIL. If you have a two-coil setup, you need to realize the resistance is halved, not doubled. Hence, if you install two 0.30 ohm coils, the resistance will be 0.15 ohms.

What’s the best vape coil for an RDA?

The new SMOK Tank coils are about as close as one can get to the performance of an RDA, but if you install one of our exotic pre-built vape coils into your RDA, you’ll appreciate the difference. Since we began selling our custom-built vape coils years ago, the most popular style is the Fused Clapton.

What is the resistance of your pre-built coils?

Please note that many of our pre-built coils are very low resistance, including some under 0.30 ohms. You need to make sure your atomizer, mod, and vape batteries can handle the low resistance. Also, make sure your RDA has post holes big enough to fit the legs of the coils. It’s also important to remember that our resistance listed is for ONE COIL.

What is the resistance of a 2-coil coil?

If you have a two-coil setup, you need to realize the resistance is halved, not doubled. Hence, if you install two 0.30 ohm coils, the resistance will be 0.15 ohms. If your mod cannot handle that low of a resistance, you’ll probably see a message like “short” or “coil missing.”