In some occasions, you will have to write an essay in the extremely short amount of time on the exam in college or high school. Also, you may be a little bit of a procrastinator, and find yourself in a situation when the paper is due tomorrow morning, and you have not even chosen the topic yet. Even though a last-minute essay cannot look as great as a work prepared successively and carefully within the whole time given, you still have a chance to submit a decent paper. The working process will require your full attention and a lot of effort, even if you are assigned a simple essay. However, if you learn the next few tips, the essay writing will seem significantly easier and feasible even when you are short on time.

Firstly, clean up your working space to get started. Make sure you have everything you need on the table, take a pen, a few sticky notes, your laptop, and read through the assignment requirements. In case no prompt is given, search for good essay topics, and pick a few uncommon and interesting ones you will be able to write about. Making a final choice, think which topic is the most relevant to your current studies and will not take too much to research.

Afterwards, look for the most trustworthy sources or the ones you are certainly allowed to use. If you are not sure, access the online library or any free services where you can look for the books and articles for your essay. Use sticky notes to write down the information and put them in front of you to see how much data has been gathered and if you need to continue researching. Reread these notes from time to time and cross out the info you do not find relevant anymore.

When you have the data you need to produce a quality work, it is crucial to think about the structure of the future paper. If you are not sure how to write an essay outline properly, check what your essay type is first. Each type is organized differently, so you need to look up the structure every time you are given an essay homework. You can also search for an example of the essay on your topic, and adhere to its outline. No matter what kind of essay you are going to write, it is important to start with a thesis statement. It should declare what problem you will review in the paper, and which facts or arguments you will use to do it professionally. As these arguments will be discussed in the main part of the essay, outline the body paragraphs and put down a few sentences with the rough description of each paragraph. Think of the way you will engage the reader in the introduction, and which thought will be conclusive for the paper. When the direction of the work is clear from the outline, use it to draft the first version of the essay.

If you are not used to model essay writing, do not worry - your draft should not necessarily look like a masterpiece. It is only the depiction of your thoughts, and as you will have them written down, it will be easier to create a good essay. There is no best way to write an essay, so trust the working methods you usually use. You may like taking short breaks once in a few minutes, or write everything in one sit - just make sure to keep the focus on writing and avoid the urge to call a friend or watch something online. Thus, you will finish the paper faster, and will not feel guilty for engaging in other activities afterwards.

Do not forget to go through the essay a few times after the completion. Everyone makes typos and mistakes by accident, but it is about you to find and fix them before your teacher does. If you need help with an essay editing, try asking a friend or a family member to read and analyze your work. Also, you can order editing services in case your paper needs to be perfectly polished so that you can submit an ideal essay and get an excellent grade.

As these steps are simple to follow, you will not have any problems coping with an essay on time. Try the whole procedure at least once, and you will not have to use any other tips preparing an essay paper during your studies!

Is parkerizing the same as bluing?

Parkerizing is a oxide finish that is porous and holds oil. It was an inexpensive finish that could be redone easily without a lot of polishing at a depot. Blueing is a hard oxide that both seals the metal and resists wear. It is more work to refinish a gun but it adds a hard shell finish.

How do you make manganese phosphate?

The manganese phosphate coating process includes a specific sequence that normally includes degreasing and cleaning of the metal part, a water rinse, then pickling in mineral acid. This is followed by another water rinse, activation, manganese phosphate, water rinse and lubricating with special oils.

What is parkerizing treatment?

Parkerizing is a method of protecting a steel surface from corrosion and increasing its resistance to wear through the application of a chemical phosphate conversion coating.

What color is manganese phosphate?

Manganese phosphate coatings, unlike zinc phosphate coatings, also provide continued wear protection after initial break-in. The coating is formed via immersion in a dilute phosphoric acid solution and is dark grey in appearance.

Can you blue over parkerizing?

“You can finish a parkerized finished handgun with a polished blue. However, the cost is much more expensive, and the polished blue finish will show all finger prints and scratches very easily.

Will a parkerized gun rust?

Without the oil or grease, a Parkerized finish will rust faster than more common (and advanced) finishes.

What is the difference between black oxide and black phosphate?

Phosphate runs at roughly 180 degrees F while black oxide runs at 290F. Both processes have similar pre-treatment steps. Black oxide gives a deep black color while phosphate coatings are grayish. Black oxide is more abrasion resistant than phosphate.

What is the difference between zinc phosphate and manganese phosphate?

A short but simplistic answer is that zinc phosphate is a pretreatment for components that will be painted or powder coated, and manganese phosphate is an oil-retentive final coating normally used for lubricated components such as internal engine parts.

Is black nitride better than Parkerized?

Phosphate is just basic parkerizing and will provide minimum corrosion resistance. It’s also porous and will make cleaning more difficult. Nitride is even harder and more corrosion resistant than chrome lining and produces sharper rifling which increase accuracy.

How do you make zinc phosphate solution?

A process for producing zinc phosphate comprising treating zinc oxide with phosphoric acid in an aqueous medium at a temperature ranging from 70° to 80° C. in the presence of metallic zinc taken in an amount of from 1 to 10% by weight of zinc oxide, followed by separation of the resulting residue of zinc phosphate.

What is a black phosphate coating?

Black phosphate is a common surface preparation for further coating or painting as it is porous with excellent adhesion. Application: Standard finish for drywall screws, however this finish is most commonly used as a pretreatment for further plating. Appearance: Dull grayish black.

Can you Parkerize over rust?

Parkerizing was originally developed to be an undercoat for paint. When parkerized metal rusts, it’s under the coating and like almost all gun finishes, once the finish is compromised there’s usually nothing that can be done short of a strip and refinish.

How do I mix Parkerizing solution?

Parkerizing Solution is a concentrate and should be mixed with 4 parts water. Parkerizing requires a heated stainless steel tank.

What is the difference between black dip and Parkerizing solution?

Black Dip should be used as is without diluting and can be used in any container other than stainless steel. Parkerizing Solution is a concentrate and should be mixed with 4 parts water. Parkerizing requires a heated stainless steel tank.

Why not just buy a premade Parkerizing solution?

It works great as either the base for a top finish, such as Molyresin or as a finish all by itself. You may be wondering “why not just buy a premade formula such as the great parkerizing solution from Brownell’s” – the short answer is because tinkering can be fun and more rewarding. I like to experiment and try different things.

What can I use to heat up my Parkerizing tank?

Just to show how simple your parkerizing tank can be, I did a batch of parts in a small stainless steel pot; the sort of thing you could find at your grocery store. If you’re only parkerizing small parts, you can use a small stainless steel pot for your tank. Much like the tank, you can use almost any kind of heat source.